CCNP SWITCH 6 – BitRadius. Instructor Lab Manual Book everyone. Download file Free Book PDF Ccnp Switch Instructor Lab Manual at. CCNP: Implementing Secure Converged Wide-area Networks v – Lab Copyright © Ensure that the switch is set up so that both the router and host are in the same. VLAN. .. Figure Internet Explorer Security Alert Prompt. ccnp switch instructor lab pdf. CCNP SWITCH Instructor Lab Manual. This document is exclusive property of Cisco Systems, Inc.

Author: Goltiran Gosida
Country: Mali
Language: English (Spanish)
Genre: Sex
Published (Last): 3 May 2015
Pages: 358
PDF File Size: 16.45 Mb
ePub File Size: 1.41 Mb
ISBN: 855-7-77499-291-3
Downloads: 34907
Price: Free* [*Free Regsitration Required]
Uploader: Kazrashakar

On DLS1, you can see the port priorities have changed, although all ports are still forwarding because it is the root switch.

Verify connectivity from the Gateway router using the ping command.

Verify your configurations using the show vlan brief, show vtp status, show standby instryctor, and show ip route commands. HSRP negotiates and determines which switch accepts information forwarded to the virtual gateway IP address.

If you are accessing your equipment remotely, ask your instructor for instructions on how to do this. Verify connectivity between VLANs. Background The current network equipment includes a distribution layer switch and two access layer switches. Shut down all the ports on your current root switch. Compiled Fri Jun Management Interface IP Address: Depending on the router or switch model and Cisco IOS Software version, the commands available and output produced might vary from what is shown in this lab.

Number of statistic hours kept: Issue the show interfaces trunk command on each switch. Apply a similar configuration on DLS1.

DLS1 show span mst configuration Name [CISCO] Revision 1 Instance Vlans mapped 0 ,, 1 2 80, Why do the switches wait until you are finished making changes to MST to commit them, rather than changing MST as you enter commands like most switch commands? Check the configuration using the show ip access-list and show ip interface vlan vlan-id commands.


To add names, use the name command in VLAN configuration mode.

Use the show ip interface brief command to verify the interface configuration and status. CEF is enabled by default on the switch. This might require a password.

This lets you have workgroups within an organization while keeping them isolated from each other. After the cables are connected spanning tree is initiated and the switch detects the redundant links.

Use the show interfaces description command to verify the interface status and description assigned. Once authenticated, the user is allowed access to the network resources.

CCNP SWITCH Lab Manual, 2nd Edition

Ports are identified as trusted or untrusted. We don’t recognize your username or password. Switch configure terminal Enter configuration commands, one per line. The switch warns you insttuctor the possibility of creating switching loops. Because you have not configured any MST region settings, the switch shows the default settings. Other switches such as a or aand Cisco IOS Software versions can be used if they have comparable capabilities and features.

The default VTP mode for the and switches is server mode.

Using a single command at switcn interface inztructor, you can implement both trust boundaries and QoS features. Now, bring up the port by issuing the no shutdown command on the interface. First, look at the current port costs using the show spanning-tree command. Configure trunk links and EtherChannel on switches. This can avoid a mutual deadlock between two switches when they consider themselves as This command displays the type of EtherChannel, the ports utilized, and port states.

Related Articles  EN 1591-4 EBOOK

Verify the configuration with the show etherchannel load-balance command.

A port on the switch can operate in one of three modes, and a port on the switch can operate in one of five modes. Statically set the switch port mode to access, and use Spanning Tree PortFast on the interfaces. These switches can be used to manage all other switches in the VTP domain.

To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. Configure access ports to trust IP phone CoS. Verify the configuration using the show port-security interface command. During this period, the switch discovers if it is connected to another switch or an end-user device. A client that runs DHCP instructro soon as it starts up benefits, because the DHCP requests could be ignored if the port was not in the spanning tree forwarding state.


Prepare for the next lab by removing all mqnual VLAN information and configurations. To choose which port becomes the root on a non-root switch when faced with equal-cost redundant root paths via the same neighbor, the switch looks at the port priorities first.

Resetting system with new configuration Because this configuration is not intended for normal operation, remove it using the no spanning-tree guard root command.

Previous post: